Weboldalunk használatával jóváhagyja a cookie-k használatát a Cookie-kkal kapcsolatos irányelv értelmében.

ImmersionRC Tramp/Ghost Hybrid UNO V2 2.4GHz Rx & 25-600mW 5.8GHz VTX

62.97 EUR
48.97 EUR
Discount: 14.00 EUR
Discount: 22%
Model: irc_tramp/ghost_hybrid_uno_v2


About this product

The new ImmersionRC Tramp/Ghost Hybrid UNO V2 is a high-end analog 5.8GHz 25mW - 600mW video transmitter and 2.4GHz diversity receiver!

There is nothing like the experience of flying an FPV drone, but building these marvelous machines is more complex than it needs to be. With Tramp, ImmersionRC has set out to raise the bars on video transmitter technology. With Ghost, ImmersionRC has set out to redefine the norms in receivers for R/C control. And now ImmersionRC has fused these two together in the groundbreaking Ghost Hybrid. Designed by pilots, built by pilots, supported by pilots.


20 x 20mm Mounting

Single-sided PCB with gummies included

Only 2.2g, perfect for the sub-250g class

Long-range AND low latency

250Hz updates

2.4GHz LoRa and FLRC Control

5.8GHz 1-600mW Video Transmitter

All 48 Standard Channels

Thermally regulated, Factory calibrated

500Hz/1kHz ready for when OpenTx can supply quality data at this rate

Available vTx channels and power may vary from region to region to comply with local regulations

2.4GHz ISM Band

Tiny 15 x 12mm, and 0.61g

Crazy Race Performance, 222.22Hz updates (500Hz Ready)

4ms End to End Latency (2ms ready), with OpenTx Integration

Fully supported by Betaflight with GHST driver


Downlink RF Power: +13dBm

Sensitivity: -117dBm in Long Range mode

Serial Formats: GHST, SBus, SBus-Fast (200k), SRXL-2 (400k), SBus Inverted

Firmware: Over-the-air (OTA) upgradeable (Rx and VTx)

Power Supply: 5V, with Over Voltage Protection

VTX Control: Automatic, via Ghost

Antenna Connectors: Standard U.FL with Locking Connectors

Dimensions: 26mm x 126mm, 2.2g (w/o antennas)

Intelligent VTX Control

Intelligent, and direct control of the video transmitter from the Ghost ecosystem. Use either the OLED menus on the Ghost Transmitter module or the responsive OpenTx tools menu. Tx remains silent on power-up, shuts down immediately in an (unlikely) failsafe.

Locking Connectors

Innovative locking connectors deliver the advantages of the lightweight u.FL/MHF standard, with the security required for world-class racing, or long-range flying. Simply plug the connector onto the board, and slide the locking cap to secure.

Thermal Regulation + Calibration

As with all tramp products, the Hybrid includes automatic thermal regulations, protecting the video transmitter against potentially damaging overheating while sitting on the starting pad. The onboard Tramp is factory calibrated, for precise power delivery during critical race events.

qTee Antennas

qTee, a.k.a ‘Cutie’ antennas are center-fed dipoles, with integral balun to ensure no cable radiation, and without unexpected nulls in the radiation pattern. Tip to Tip length of just 60mm, easy to install in anything from a Whoop™ to an X-Class quad


Firmware/ Downloads


Antenna connector IPEX (u.FL)
Dimensions (Length * Width * Height) 26x26 mm
Input voltage 5 Volts
Mounting pattern 20x20 mm (micro)
Radio frequency 5.8 GHz
Weight 2,2 g

Package included

1 x ImmersionRC Tramp/Ghost Hybrid UNO V2 2.4GHz Rx & 25-600mW 5.8GHz VTX

1 x Silicone Cable

2 x qTee Antenna


There are no reviews for this product.
Write a review!